{"id":5852,"date":"2013-01-18T07:37:14","date_gmt":"2013-01-18T15:37:14","guid":{"rendered":"http:\/\/rustybolt.info\/wordpress\/?p=5852"},"modified":"2013-06-23T09:46:50","modified_gmt":"2013-06-23T16:46:50","slug":"213-01-18-watsons-wireless-joule-thief","status":"publish","type":"post","link":"https:\/\/rustybolt.info\/wordpress\/?p=5852","title":{"rendered":"2013-01-18 Watson’s “Wireless” Joule Thief"},"content":{"rendered":"

\"\"<\/a>I was watching Sohei’s “wireless” light<\/a> on Youtube and I decided to build a similar one.\u00a0 It’s not much different from the Tesla pancake coils I was experimenting with recently<\/a>.\u00a0 This “wireless” Joule Thief is not really wireless, because it doesn’t really radiate radio frequency energy.\u00a0 It’s just a transformer with the secondary winding separate and independent from the primary winding, with the energy coupled electromagnetically.<\/p>\n

To make the coil, I used a hank of white wire from a ten foot parallel printer cable, and a shorter hank of wire from a six foot cable.\u00a0 They are both 26 AWG, and the longer one is the primary (collector) winding and is about 23 uH and 0.232 ohm DC resistance.\u00a0 The shorter one is the feedback (base) winding and is about 13 uH.\u00a0 They’re just put together and\u00a0 tied down to the piece of plywood with some short lengths of wire.\u00a0 The inside diameter is 2.8 inches or 70mm.\u00a0 The secondary (LED) winding is about 22 uH but it looks thinner, maybe 28 AWG white wire and is 0.345 ohm DC resistance.\u00a0 The LED is just soldered to its ends.\u00a0 The other parts are soldered to the heads of small screws that I put into the plywood at various locations.<\/p>\n

The transistor is a 2SC2500D, which is really hard on the AA cell.\u00a0 The resistor is the standard 1k, 5%, 1\/4 watt resistor.\u00a0 The two amber LEDs are in series and are connected between emitter and base with the cathodes toward the base.\u00a0 They prevent the base voltage from going more negative than 6 volts, and you can see they are glowing slightly, showing that the base voltage is going down to negative 6 volts.<\/p>\n

The circuit draws 400 mA from the 1.5v supply, and the AA cell doesn’t last very long.\u00a0 The 2SC2500D is a very high gain power hungry transistor and sucks a lot of current.\u00a0 I could reduce it by increasing the value of the resistor.\u00a0 The white LED is not lit very bright because the secondary coil is not centered over the primary.\u00a0 When I put it directly over the primary the LED gets much brighter.\u00a0 But the LED is polarity sensitive: if I flip the coil over, the LED is much dimmer.\u00a0 I think this coil needs some more turns; the LED is not as bright as it could be, considering all the current that the circuit is drawing from the AA cell.\u00a0 I’m going to experiment with this coil some more.\u00a0 I have also placed the chokes from the pancake coil inside of this coil and the LEDs light up.<\/p>\n

Update Jan 19 – I changed the secondary to a coil having a much longer wire,\u00a0 It measured 0.625 ohm and 56 uH.\u00a0 The LED lights up much brighter, and is beginning to act like a flashlight or light, as Sohei showed in his video.<\/p>\n

\"DSC_0381S2\"<\/a>Update Jun 22, 2013 – I added a half wave voltage doubler to the picjup coil between one of the coil wires and the anode of the LED.\u00a0 But the LED serves as the second diode, and there is no filter capacitor.\u00a0 This arrangement reduces the loss and helps the LED when the pulses are negative going, since it captures the negative going pulses.\u00a0 I used a 0.1 uF capacitor between the coil wire and the diode, which was a 1N4148.<\/p>\n","protected":false},"excerpt":{"rendered":"

I was watching Sohei’s “wireless” light on Youtube and I decided to build a similar one.\u00a0 It’s not much different from the Tesla pancake coils I was experimenting with recently.\u00a0 This “wireless” Joule Thief is not really wireless, because it doesn’t really radiate radio frequency energy.\u00a0 It’s just a transformer with the secondary winding separate <\/p>\n

(Read More…)<\/a><\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[4,13],"tags":[],"class_list":["post-5852","post","type-post","status-publish","format-standard","hentry","category-joule-thief-smps-dc-dc","category-lighting"],"_links":{"self":[{"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=\/wp\/v2\/posts\/5852","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=5852"}],"version-history":[{"count":21,"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=\/wp\/v2\/posts\/5852\/revisions"}],"predecessor-version":[{"id":5855,"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=\/wp\/v2\/posts\/5852\/revisions\/5855"}],"wp:attachment":[{"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=5852"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=5852"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/rustybolt.info\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=5852"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}